Installation Video

For Easy installations of modular, custom built walk-in coolers, freezers, temperature controlled rooms

Toll Free Customer Support 1-855-890-3400
Walk-in coolers, Walk-in Freezers,
Refrigerated Warehouses, Blast Freezers,
Cold Rooms, Refrigeration Systems,
Refrigerated Warehouses,
Processing Rooms,
Walk-in Doors
Sales, Services & Installation


Installations Instructions for modular, custom built walk-in coolers, freezers, temperature controlled rooms

Inspection on delivery

Each panel will be marked at the factory, designating walls, floor, and
ceiling panels. A floor plan is provided to assist you.

Please take time to inspect all panel boxes prior to signing for shipment,
making a notice of any damage on the delivery ticket. If concealed damage
is discovered, save carton and immediately contact carrier agent to initiate
inspection and claim. Please remember, although we will assist you in any
way we can, this is your responsibility.


Handling of Panels

 

Your panels were inspected prior to shipment and loaded in good condition,
damage can occur if not properly handled, while unloading and erecting your Walk-In. If ground is wet, slack panels on a platform to avoid contact with the ground. If panels are placed in outdoor storage, cover with moisture proof sheeting. When handling panels keep them plat to prevent denting, and avoid
resting them on their corner edges. Always use sufficient man power to eliminate mishandling or dropping panels.


Prepare your site

 

Please be sure the area is free of debris and swept clean. Next "chalk" the perimeter outline of the structure and confirm its "square" by checking
diagonal measurements.

 

Floor Panels

 

After you have cleared the debris and swept installation site clean, use a
chalk line to outline the position of panel walls, mark a line to indicate
the overall length of the Walk-In. Refer to the installation drawing provided,
for the proper diagonal dimension. Care must be taken to properly level and support the panels with shims. An un even floor results in a faulty solution.

Before you begin place polyethylene sheathing or 50 lb. asphalt paper
floor panel and existing floor.

1.On your level floor end section in the correct location according to the diagram provided. Be sure the panel is level in weight and width.

2.Next, place the appropriate panel section into position. After making
sure the edges are flush, lock the panels together.

3.As you assemble your floor, check to insure that the existing floor is
level, and the chalk-line is followed.

4.Follow this procedure till the last panel is in place, this panel must be an end section

 

Floorless Installation

 

1. Prepare site, sweep clean and remove debris.

2. If it is an inside installation adjacent to a building allow enough space for proper ventilation.
(Approximate 3"-5")

3. Establish your chalk line to define panel wall location

4. Refer t your installation drawing, (Provided) for outside and inside dimensions of panel, and Walk-In
length and depth. Check diagram for outside corner-to-corner diagonal dimensions.

5. When points are square, use chalk-line to mark outside panel walls.

6. You may find it easier to mark the interior wall line. Just measure 4" from your outside lines and use chalk to mark. You may wish to place screeds into position around perimeter at this time.

7. Apply a bead of sealant along each chalk line. Carefully place screed on chalk line pressing down firmly. Next secure screed in position. Note: Use only NSF listed silicone sealant.


Wall assembly

 

Review installation drawing provided, select a rear corner panel, place it even with outside of base, and partially lock it into position. Select a wall panel on either side of the corner, firmly snap these panels to the corner, making sure tops are level. A corner panel must be the last panel erected.

 

Doors

 

When installing entrance doors, we do not suggest removing the door from the doorjamb. Doing so will cause the spring assisted cam-lift hinge to loose the factory set tension, and the door will not operate as manufactured. We suggest using at least two men when handling and erecting, (being extremely
careful not to drop or twist the door section) door panel. When door section is in place check doorjambs for plumb and level proper door closing.


Ceiling panels

 

Refer to the installation drawing provided, choosing the ceiling panel adjacent to ceiling wall. Place the end panel properly aligning it with corners, front, back, and side wall, but not walls at "open" side. Select next panel, carefully align to end panel and walls. Snap together along center seam. Engage top wall locks into Ceiling and engage snap-locks, but do not fully tighten. Continue placing ceiling
Panels, aligning, locking and tacking to walls, until last panel is in place. After
carefully checking corners and perimeter complete locking to walls.


Indoor Installation

 

For a ceiling over 16 ft. long, a suspended support system will be supplied.
Supports should be installed as per engineering drawing supplied by factory.

 

Outdoor Installation

 

For outdoor, a rain proof cap is recommended. Outdoor rain proof
membrane is 40-mill polyester fabric. White to reduce heat gain and
save refrigeration cost. The roofing material is fabricated from high
tenacity low shrink polyester that has been coated with a new
thermoplastic alloy. This specialty formulated permanent thermoplastic
alloy will not migrate from the coating like conventional plastecizers;
it is resistant to ultra-violet rays, microorganisms and non-wicking.
The tear and puncture strength from the polyester are superb and
it is impervious to most caustic chemicals, petroleum products and
acids. It also shows no ill effect to heat or cold.

Rain roof installation instructions

Place vinyl roofing material, with flaps underneath, on to of Walk-In across
narrow end. Allow 6" of vinyl to lap over each of the three sides. Carefully
unroll vinyl material until vinyl flap falls into position. Then screw a plate
at each end of flap. Keep placing until your end up with a screw and flap
every 12". Continue to roll out vinyl until the end next flap, and then repeat
screw down process. Once the end is reached, it should lap over the end by at
least 6". Place a bead of caulking around topsides of Walk-In with stainless
steel screws. Fold corners and continue around box on all four sides.

 

Our clients

Floral Refrigerated Building

Floral Refrigerated Building

Sample image

Refrigeration Systems for Refrigerated Warehouse

Sample image

Insulated Metal Panels

Sample image

Walk-in Coolers and Walk-in Freezers